Before first use, be sure to review important safety information.

YOUR FIRST BLEND…

  1. Using the included USB-C cable, you can charge your BlendJet with most USB ports, from your phone charger, to your computer, to the USB port in your car.

  2. Your BlendJet takes about 1.5 hours to fully charge, and lasts for 15+ blends.

  3. The light ring around the power button indicates battery level while charging. As your BlendJet charges, the lights will change from purple to blue. When the light around the power button forms a complete blue circle, your BlendJet is fully charged.

  4. The circle turns purple (instead of blue) while blending or pulsing whenever the battery is getting low.

  5. The circle will flash red and purple when the battery is dead and it’s time to recharge.

.

CHARGING

  1. Using the included USB-C cable, you can charge your BlendJet with most USB ports, from your phone charger, to your computer, to the USB port in your car.

  2. Your BlendJet takes about 1.5 hours to fully charge, and lasts for 15+ blends.

  3. The light ring around the power button indicates battery level while charging. As your BlendJet charges, the lights will change from purple to blue. When the light around the power button forms a complete blue circle, your BlendJet is fully charged.

  4. The circle turns purple (instead of blue) while blending or pulsing whenever the battery is getting low.

  5. The circle will flash red and purple when the battery is dead and it’s time to recharge.

CLEANING

Always clean your Blendbreak immediately after each use to prevent food from drying and sticking to the blades. Your Blendbreak is water-resistant, so it’s okay if the USB port gets wet, but never put your Blendbreak—including the base, jar and lid—in the dishwasher, or submerge it entirely under water.

  1. Remove the jar from the base: twist the jar counterclockwise while twisting the base in the opposite direction.

  2. Using a fork, carefully remove the silicone gaskets from the lid and base for a more thorough clean. Take note of which gasket goes where, as the two are slightly different. The one with the groove goes in the base.

  3. Wash the jar, lid and gaskets in soapy water.

  4. Use a dish brush to dislodge any debris around the blades, if needed. Never put your hands in the path of the blades.

  5. Each part should be left out long enough to fully air dry.

  6. To reassemble your Blendbreak, place the grooved gasket back in the base. Make sure the grooved side is facing down. Use the tip of a spoon, if needed, to press it firmly into place. This will help to prevent leaking. Next, place the jar on top and screw it into the base to push in the gasket fully.

  7. Place the second gasket back in the lid, pushing it it into place with either your fingers or a spoon.


IMPORTANT SAFEGUARDS & CAUTIONARY INFORMATION

Please review these precautions carefully before using your blenderPro for the first time.

DO’s

DO store your blenderPro in a secure place, out of the reach of children.

DO use only high-quality USB chargers (like the one that came with your phone) and USB-C cables (like the one that came with your blenderPro).

DO allow ingredients to settle in your blenderPro before you unscrew the lid after blending.

DO’S

DO operate your blenderPro with the lid securely screwed on.

DO firmly push the USB cable all the way in to charge (do not plug it in partially).

DO take care when handling the base of the blender without the jar attached. As a safety precaution, there are magnets in the jar and base of the blender that must be aligned for blenderPro to work. Magnetic objects can fool the base into thinking that the jar is attached and allow the blades to spin.

DO NOT put MCT oil (or powder) in your blenderPro; over time, this can damage the blender.

DO NOT run your blenderPro while it’s empty as this can damage the blender.

DO NOT allow the charging cable to touch hot surfaces.

DO NOT immerse the charging cable in water or other liquids to avoid risk of electric shock.

DO NOT charge your BlenderPro when it’s wet. Use only high-quality USB chargers (like the one that came with your phone) and USB-C cables (like the one we’ve included).